Steering Console (MCC-101)

kormanykonzol.png

Contents of the equipment package:

– Handlebar bracket 1 pc
– M4x16 A2-70 screw 2 pcs
– M5x20 A2-70 screw 1 pc
– D5 spring washer 1 pc
– Rubber washer 1 pc
– Crank arm 1 pc
MCC-101_1.png

1. Measure the diameter of the steerer tube.

The mount is suitable for handlebars between 20 and 30 mm in diameter. If you would like to mount it on a tube with a diameter of less than 20 mm, you will need the reducer adapter sold under the name MCC-120. With its help, the mount can also be attached to a 12 mm tube.
MCC-101_2.png

2. Attach the bracket to the handlebar stem.

then tighten the 2 M4 screws. If necessary, you can use the included rubber washer to protect your painted or otherwise treated handlebar from damage. In addition, the rubber sheet also helps with vibration damping. The chosen device can then be mounted onto the bracket.
MCC-102

Mirror console

MCC-102.png

Contents of the equipment package:

– Mirror bracket base plate 1 pc
– M5x20 A2-70 screw 3 pcs
– D5 spring washer 2 pcs
– Short extension 1 pc
– Long extension 1 pc
– M5 self-locking nut 1 pc
mcc-102_1.png

1.

Measure the bolt spacing on the brake/clutch lever clamp. The bracket is suitable for a bolt spacing between 29.5 and 33.5 mm.
mcc-102_2.png

2.

Unscrew the bolts securing the clamp. The bracket is typically mounted with cylindrical head bolts. If the bolts are countersunk, it is necessary to use the spacers included in the package. In this case, longer bolts than the original ones must be used. These
are not part of the kit.
MCC-103

Clamp bracket

bilincs_konzol.png

Contents of the equipment package:

– Clamp bracket base plate 1 pc
– M5x20 A2-70 screw 3 pcs
– D5 spring washer 2 pcs
– Short extension 1 pc
– Long extension 1 pc
– M5 self-locking nut 1 pc
– M6-10 mm spacer 2 pcs
mcc-103_1.png

1.

Measure the bolt spacing on the brake/clutch lever clamp. The bracket is suitable for bolt spacings between 29.5 and 33.5 mm.
mcc-103_2.png

2.

Unscrew the bolts securing the clamp. The bracket is typically mounted with cylindrical head bolts. If the bolts are countersunk, the spacers included in the package must be used. In this case, bolts longer than the original ones must be used. These
are not part of the kit.
MCC-104

Brake fluid reservoir bracket

MCC-104.png

Contents of the equipment package:

– Console base plate 1 pc
– M5x20 A2-70 screw 3 pcs
– D5 spring washer 2 pcs
– M5 cap nut 1 pc
– Short extension 1 pc
– Long extension 1 pc
mcc-103_1.png

1.

Measure the distance between the bolts securing the brake reservoir cover. The bracket is suitable for bolt hole spacings between 36 and 73 mm. The bolts can be M4 or M5 size. The cover is typically fitted with countersunk bolts; these must be replaced with cheese-head bolts, and the use of a washer may also be required.
mcc-103_2.png

2.

Attach the bracket to the brake reservoir cap. Then, insert the new screws and tighten them. If necessary, you can adjust the phone's position using the included Short and Long extension pieces.
MCC-106, MCC-107, MCC-108

Center console

MCC-106-107-108_05daf781-e239-4688-962d-f319b83100bd.png

Contents of the equipment package:

– Handlebar stem bracket 1 pc
– M6x50 bolt 1 pc
– M5x20 A2-70 bolt 3 pcs
– D5 spring washer 2 pcs
– M5 nut 1 pc
– M4x6 countersunk bolt 1 pc
mcc-106_1.png

1.

Measure the diameter of the steering shaft hole. The bracket is available in 3 sizes: 14-18 mm, 18-22 mm, and 22-26 mm in diameter. Choose the bracket size that is right for you.
mcc-106_3.png

2.

Insert the bracket into the hole. Then, tighten the M6 countersunk screw until the bracket is secured in the hole. Place the base on top, then fasten the two M4 screws.
MCC-109

M8 console

m8_konzol.png

Equipment package contents:

– M8 bracket 1 pc
– M4x6 A2-70 screw 2 pcs
– M5x20 A2-70 screw 3 pcs
– D5 spring washer 2 pcs
– Bracket base 1 pc
– M8x60 A2-70 screw 1 pc
– M5 nut 1 pc
mcc-109_3.png

1.

The bracket is designed for the M8 bolts that secure the handlebar. The bracket is made to be suitable for replacing cylindrical head countersunk bolts. The bracket is suitable for use in bolt locations with a minimum diameter of 13 mm and a maximum countersink depth of 15 mm. Naturally, the bracket can be installed in place of any M8 bolt.
mcc-109_1.png

2.

Loosen the selected screw! Then, position the bracket and the longer screw. You may require a screw different from the one provided. The new screw must be 20 mm longer than the original.
Finally, screw the base onto the bracket using the provided M4 screws.